![\"\"](\"http:\/\/www.nordahlia.com\/wp-content\/uploads\/2013\/01\/IMAG24651.jpg\" "\\"IMAG2465\\"")
<\/a><\/p>\nSnip the corners, turn it right side out, and poke the corners out with this corner-poking tool:<\/p>\n
Press the pouch. Before:<\/p>\n After:<\/p>\n Eek, I ironed off the velcro! No, it’s on the other side. I had you for a minute there, didn’t I.<\/p>\n Don’t worry; I’m not going to justify that “question” with a question mark.<\/p>\n Double-sided tape to hold the velcro in place and pull the back fabric taut:<\/p>\n I cut the raw edges fairly close, then folded them inside and pinned:<\/p>\n Larry made an extended table for the sewing machine, which was necessary for sewing something this stiff that had to be kept flat.<\/p>\n Here is a shot of it being slightly more visible:<\/p>\n I broke into the Chinese New Year panels for some emergency velcro-sewing on some regular panels. There is a gap between the back of the sewing machine bed and the extension because the base didn’t take into account the width of the knee foot-raising lever.<\/p>\n Which I also had a hard time remembering to take into account. The first several panels, I snipped the threads with a physical scissors instead of the\u00a0auto-snip scissors button. Since I associate my hand (upper body) with raising the presser foot and my foot (lower body) with making the machine run, trying to associate my knee (lower body) with raising the foot kept messing up my internal autopilot; I kept mixing up making the machine go with the knee-raiser and pushing the pedal with raising the presser foot. Other times, I would raise the foot by hand and by knee at the same time or confuse the fact that the knee raises the foot temporarily while the hand lever raises it until you manually lower it.<\/p>\n We needed a couple dozen velcro strips, which wouldn’t truly test the new machine’s ability to handle the X-treme glue (no sic), but it could start to give an idea, as well as mentally prepare Speedy for his real full-time job that does not include hours of sewing on luxurious taffeta.<\/p>\n Here is what the glue looks like collected on the needle:<\/p>\n That’s the accumulation from just one strip.<\/p>\n So far it does not seem to be getting down into the bobbin case or sticking to the bottom of the presser foot. Or getting into the feed dogs or lining the bottom of the needle plate.<\/p>\n These needles don’t really have much of an indent running down the shank, so the glue doesn’t build up in there. The side-loading needle so far seems to handle the glue and keep the thread away from it better than the usual front-loading needle.<\/p>\n One sort of problem I’ve noticed with this machine is its ability to corner:<\/p>\n And again, to show that this is not an isolated incident:<\/p>\n Though in this one, you can see where it’s trying.<\/p>\n Coming up slowly on the corners–and of course coming to a complete stop, raising the presser foot, then turning the fabric–does not seem to have any effect on its tendency to Tokyo drift.<\/p>\n Anyway, back to the New Year panels:<\/p>\n Because the process involves so many steps, and because doing all of one step before moving on to do all of the next step takes less time than cycling through all steps for one or for a small group, I tried to production-line as many stores at once as I could. They’re all divided up by very specific quantities and sizes–down to a half-inch difference between the panels for one store or another. So here is the mess of multiple stages going on and being kept carefully separate.<\/p>\n <\/p>\n","protected":false},"excerpt":{"rendered":" Usually for these panels, I just stitch on the velcro, then someone else glues the fabric to the backing. This taffeta fabric chosen to decorate for the Chinese New Year was too thin and the glue left visible dark spots. … Continue reading <\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n<\/a><\/p>\n